Ring Filter Adapter

Account limit of 2197 requests per hour exceeded.

Reverse Osmosis Water Filter Installation And Replacement Of Steps

Automatic reverse osmosis pure water machine is a kind of microcomputer automatic control of the terminal for effective water treatment facilities, convenient installation. When you purchase or install the machine for the user, in order to ensure the installation of quality, usually can be installed the following order: Install RO Membrane Precision activated carbon fiber filter filter drilling install fiber filter host install water shut off the main valve Links water through installation of water through to the fiber filter is leaking water mains test install storage bucket Ball gooseneck faucet gooseneck faucet to the rear of the carbon export ratio of water to the sink waste pipe post-carbon pipe connected to the front Power supply Detection of water quality and stable water quality compliance link water storage bucket of water on the ball Drainage end of the installation of water again.

II type pure water machine, under cabinet installation

(A) install RO membrane RO membrane to remove packaging film, removal of the RO membrane housing lid of the water, unscrew the RO membrane shell cover, will have two rubber seals one end of the insert within the RO membrane housing only in the mouth, turning to plug into the bottom. Shell end cap seals the membrane first moved to the RO membrane shell casing thread only the mouth, to the hand tightened in the housing cap, fitted with water pipes, tighten.

Inspection Cover Department Elbow Is loose, such as have been loose, remove it, raw wound with 2-3 laps and then spin on it as is.

Particular attention to: open the RO membrane should wash your hands before packaging, the installation process should keep hands clean and shall not cause the pollution of the RO membrane.

(B) installation of filter Removed Plastic Packaging films, will be the order of the fiber filter, particulate filter and activated carbon fiber filter insert with double seal on the side of the interface filter cap. Bottle on the filter O-put a little white apron along the periphery Vaseline, screw the bottle and hand tighten the filter, when using the special wrench, tighten the process should not be too hard to be uniform and large.

(C) the installation of a fixed host

1. Wall installation: the installation in the selected location to play two holes 8 mm in diameter. Into the onboard plastic expansion bolt, screw into the screw, hang up the host and tighten the screws.

2. Cabinet install: can not punch a fixed, stable release can be selected here.

Both installed on the wall or installed in the cabinet, should be considered in the future filter replacement and maintenance convenience. Especially when installed in cabinet, the water should be installed outside the cabinet machine operation.

3. Gooseneck faucet installation preparation: the location of the customer selected to install. Such as the gooseneck faucet conditioning to be installed in the kitchen countertop, countertop should be conditioning drill a hole diameter of 12 mm. Such as the gooseneck faucet installed in a wall, should the selected position, according to the two stent diameter drill hole distance of 6 to 8 mm hole, stuffed plastic expansion bolt, with self-tapping screws will be fixed to the wall bracket , then the order of installation of gooseneck faucet.

Hole in the marble countertop should be used when special drill bit, positioning plate with positioning. In imitation marble (synthetic material) on the drilling should be used when ordinary twist drill. The two were using ordinary hand drill hole, must not use the impact drill.

4. Reservoir bucket on the valve installed: Office entangled in the reservoir bucket 6 to 8 threaded ring seal tapes, rotating into the ball, then the hand tightened on the ball. Will be placed in storage buckets placed in the appropriate location.

5. Gooseneck faucet install: install gooseneck faucet, the above soft circle amplification, the bottom of the order of release of small soft plastic ring, hard plastic plate, metal washer, then tighten the nut.

6. Installation of pure water machine water pipes must be placed in the tube end plugs to prevent leakage.

(4) connected to the water pipe machine parts

1. Water pipeline Total indoor valve closed. Location of the user selected to install water supply and water links through (random tape), install the rear parts of water. The three parts to use sealing tape to prevent leakage.

2. Machine pipe Host the nut all the interfaces connecting the components indicate the name, the installer should be know in advance. Water purifier portable water is 5 meters, the user should take into account the use of a good length of each part of the water mains, water mains each Office butt end should be cut Sarkozy.

3. Influent through?? Fiber filter water bottle filter:

Water through: Unscrew the water inlet valve adapter nut, insert the pipe nut, plug into the pipe through the outlet on the water (to be inserted in the end), and then tighten the nut, will be placed in the closed position through water. The other end connected to the fiber filter cartridge top caps (all water pipes should end with the pipe plug to use random, to tubes inserted in the end, to the hand tighten the plastic nut).

Through various parts of the water test machine is leaking water (turn on the valve, open the rear water switch, release Sewage Until the water is clear water after the closure of the rear switch, open water through the inspection.

4. Gooseneck faucet?? Carbon rear exit pipe:

Gooseneck faucet: The interfaces were dedicated adapter to use a fixed nut: the nut into the pipe, then insert the sealed plastic apron and make water pipes exposed 1-2 cm into the pipe lower gooseneck faucet, and then spin the nut firmly set (applicable force can wrench tightened).

5. Rear carbon export: to connect the normal way of installing the pipes.

6. Wastewater ratio?? Water pipes under the sink:

Waste water than the Department connections by the general installation. The other end can receive the user's sewer (the concentration of water can also be received as a general wash of other vessels in the water).

7. Post-carbon front-end links?? Reservoir water bucket on the ball:

Here by the general installation of water connections. Typically, with the reservoir water bucket on the valve Department temporarily not connected, water quality testing to be done after the connection.

About the Author

I am an expert from Cheap On Sales, usually analyzes all kind of industries situation, such as emerson vhs , denon dvd 1920.

MASSA 62mm Filter Adapter Ring for Square P Series Filter Holder Camera Lens 2